startec ltd
Professional portable telescoping tower supplier
Add to Cart
2 Axial Portable Telescopic Mast
This mast is designed for sport fans and photographers.
This mast usually has pin locking or hand wheel brake structure. It supports by tripod, the tripod is freely nested, open , adjust the support angle.
The mast also has two or three wheels which is easy to move on the ground , reducing the labor intensity.
The mast can be stored in a canvas bag when it is not used.
This mast has three nylon guy lines and three ground stake which improves the mast stability when it is windy.
product introduction:
Telescoping mast is a mast comprised of sections which collapse into each other.
Our best-selling mast pole is made of the highest quality aluminum and built to last.
Extremely portable but ready to provide years of permanent service too!
Available in extensions from 3m up to 15m.
specification:
Hard push up
| extended height (m) | No. Of section | Retracted height(m) | Outer tube range(mm) | Self weight (kg) | Max.payload (kg) |
| 3 | 2 | 1.55 | 50-55 | 3 | 20 |
| 4 | 3 | 1.35 | 50-60 | 4 | 20 |
| 5 | 3 | 1.7 | 50-60 | 5 | 20 |
| 6 | 4 | 1.55 | 45-60 | 6.5 | 15 |
| 7 | 4 | 1.8 | 45-60 | 7 | 15 |
| 8 | 5 | 1.65 | 45-65 | 9 | 12 |
| 9 | 5 | 1.85 | 45-65 | 10 | 12 |
| 10 | 6 | 1.7 | 40-65 | 12 | 10 |
| 12 | 7 | 1.75 | 35-65 | 28 | 8 |
| 15 | 8 | 1.9 | 30-65 | 6 |
Product photo:
Application areas:
For WiFi, Portable Antennas, Elevated Photos
Ideal for:Emergency Response Antenna Systems, Restricted Space Antennas - Prepping Systems
Elevated Photography - Weather Instruments - WiFi Site Surveying - End Zone Cameras
Usually these masts require a flat or socket wrench, with the quick release clamps you can raise and lower the masts without any tools.
Even with limited space these quick clamps can be easily used, because the lever can be adjusted at any position. Just pull out and release the lever, the strong spring latches the lever at the desired position.
Attentions:
The mast can be extended to any length and securely locks into place by means of a massive clamp. The maximum allowed extended length is marked by a color ring approx. 20cm before the end of each tube. There is no fixed stop which makes it advisable to approach the marking slowly when extending the telescopes.
These masts are ideally suited for portable applications due to the low weight and the telescopic mechanism. When setting up the mast please pay special attention to the clamping length; the clamping length of the mast must be at least 1/6th of the extended length, or at least 1 meter at the minimum. When extending the mast more than 6 meters measured from the uppermost clamping point additional guys are mandatory.
The tubes are made of weather-proof aluminum alloy. The tubes are tapered by 5 mm and the tube thickness is 2mm. Please refer to the following table for weight and dimensions. The stated additional forces refer to a horizontally applied force at the tip of the extended mast - without guys and a mast clamping length of 1/6th. The calculation includes the inherent load at a wind speed of 50km/h (which is equivalent to a wind force of 7).
also we can produce according to clients special requests, and can give proposals.
Packing, delivery tiem, and shipping:
We will close then pack the goods safely in solid wooden box.
Prodcution lead time for sample: 2 weeks; 4 weeks for bulk order
Ship by sea, air, or express according to your request.